Dji Naza M Lite User Manual
- DJI's cost-effective NAZA-M Lite flight control system is a simplified version of the NAZA-M. It features the same high reliability and stability of the NAZA-M, but is tailored to entry-level enthusiasts with an innovative all-in-one design that simplifies installation, while saving space and weight.
- User Manual V 2.0 www.dji-innovations.com. 2 Warning & Disclaimer Naza is an excellent autopilot system offering tremendous flight features for low altitude multi-rotor working in restricted space compared to normal helicopter. It is not a toy when installed in multi-rotors of any size.
Harris Aerial presents the DJI Naza-M V2. DJI adheres to continuous innovation and improvement. With the new firmware, new attitude stabilization algorithm and optimized hardware structure, the Naza-M V2 provides better flight performance. The innovative All-in-One design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis.
©2014 DJI. All Rights Reserved.
8
Assembly
接电调
接云台
F1
F2
接电调
接云台
VU
·
Do not mount it on any other electronic devices. Make sure You can see the
LED light during the flight.
·
If use with DJI multi-rotor, you can solder the VU power cable to power
pads on frame bottom board. Please refer to DJI multi-rotor manual for
details.
·
If use with 3
rd
part multi-rotor, you can make a connecter by yourself to
connect VU, ESCs and battery.
·
Sufficient air flow over the VU is highly recommended.
MC
·
Please use
3M gummed paper provided To mount MC, and mount MC parallel to the
aircraft horizon.
·
The output ports of MC (the right side in figure) should point to the front of
multi-rotor. You
’d better put MC at the gravity center of multi-rotor. Please
make sure all ports are accessible when installing the MC so as to facilitate
wiring and software configuration.
·
In three-pin ports, pins near the nicks are signal pins.
·
After choosing a location to mount the MC, it is recommended
The phone is powered with 3000mAh battery with Quick Charge feature.Performance sector, Motorola Moto X4 smartphone is relatively competing in the middle class rumored to rely on Qualcomm’s Snapdragon 630 chipset that carries a 64-bit ARM Cortex-A53 octa-core processor consisting of 2.2 GHz quad-core and quad-core 1GHz speed combined with memory 3GB of RAM and supported graphics processor from Adreno 508. Not to forget, the fingerprint sensor is also included in this phone. /moto-4-phone-how-to-user-manual.html. And Moto X4 has 4G LTE connectivity, 3G HSPA, WiFi, Bluetooth, GPS, and USB Type-C port.
that you DO NOT mount the MC until all wirings and software configurations
are completed.
GPS/COMPASS
·
GPS/Compass is sensitive to magnetic interference, should be far away from any electronic
devices.
·
You should use epoxy resin AB glue to assemble the GPS bracket first as the figure showed
in previous page.
·
Mount the bracket on the center plate of craft first, then fix the GPS on the plate of the
bracket (by 3M glue provided). The GPS is sensitive to vibration interference, so position
the bracket at least 10 cm from any rotor.
·
The DJI logo marked on the GPS should face the sky, with the orientation arrow pointing
directly forward. The GPS/Compass is packaged with a special indication line for mounting
for the first time.
·
If you are uncertain whether materials near the GPS/Compass module are magnetic or not,
you can use a compass or magnet to check it. If you use your own mounting rod, make sure
it is NOT magnetic!
Aircraft Nose
R/C System
Dji Naza M Lite Manual
These are example connections. Please
setup Aileron, Elevator, Throttle, Rudder
channels on your TX first, and choose
o n e 2 positions switch/channel ( 3
positions switch with GPS) as control
mode switch, then connect your receiver
to the right ports on MC.
R/C Receiver
(JR)
RUDD
THRO
AILE
ELEV
R/C Receiver
(Futaba / Hitec)
1
2
3
4
Futaba S-Bus
S-Bus
Your Account. Login; Create an Account. Check your order, save products & fast registration all with a Canon Account ×. User Manual Library Select a Product Type below to begin. If you don't see your product listed below, please use our Manuals Finder for assistance. /canon-bg-e3-manual-download.html.
2/3-position switch channel
Optional
ESC
M1-6
To Battery
ESCs, Motors
·
Motors and ESCs in DJI multi-rotor kit are recommended.
·
Please make sure you are using the ESCs and motors recommended by the
manufacturer of your multi rotor first. NAZA-M LITE output is 400Hz
refresh frequency.
·
Connect all ESCs to MC by the motor numbering method introduced in
Multi-Rotors Supported of Appendix.
·
If you use 3
rd
Dji Naza Lite Manual
party ESCs, please make sure the ESCs travel midpoint is at
1520us. DO NOT use 700us travel midpoint ESC, as it may lead aircraft to
fly away or cause injury and damage. After connect ESCs to motors,
calibrate all your ESCs one by one through the receiver directly before
connect them to your MC, Make sure program all of them into Governor off,
Break off and Normal Start up to get best experience.
Roll
Pitch
2/3-position switch channel
Important: the continuous
output of the V U is 3A@5V, and the
maximum instant current is 7.5A. If the V U
cannot afford the working current for you r
servos, please use an independent power
supply; otherwise, it may cause the V U
safeguard and lead to the main controller
reboot.
©2014 DJI. All Rights Reserved.
NAZA-M LITE
User Manual
Dji Naza M V2 Instructions
V 2.00
2014.04.21 Revision
For Firmware Version V1.00
& Assistant Software Version V1.00
Thank you for purchasing this DJI product. Please strictly follow these steps to mount and connect this system on
your aircraft, as well as to install the Assistant Software on your computer.
Please regularly check the NAZA-M LITE web page at our website
or latest information. Product
information, technical updates and manual corrections will be available on this web page. Due to unforeseen changes
or product upgrades, the information contained in this manual is subject to change without notice.
* This manual is only for basic assembly and configuration; you can obtain more details and advanced instructions
when using the assistant software. To assure you have the latest information, please visit our website and download
the latest manual and current software version.
If you have any problem that you cannot solve during usage, please contact your authorized dealer.
www.dji.com